Glossary entry (derived from question below)
Russian term or phrase:
без пеньков
English translation:
without [blade] stubs
Added to glossary by
Oleg Lozinskiy
Feb 9, 2020 22:17
4 yrs ago
19 viewers *
Russian term
без пеньков
Russian to English
Tech/Engineering
Metallurgy / Casting
Ступица рабочего колеса турбины была выполнена литой из стали 20ГСЛ без пеньков.
Proposed translations
(English)
3 | without [blade] stubs | Oleg Lozinskiy |
2 | without blades | Frank Szmulowicz, Ph. D. |
Change log
Feb 14, 2020 11:47: Oleg Lozinskiy Created KOG entry
Proposed translations
9 hrs
Selected
without [blade] stubs
A comprehensive test campaign was performed in the Politecnico di Milano wind tunnel to compare the aerodynamic performances of the ERICA engine air-intake. Indeed, several operating conditions were tested i.e. cruise, conversion and hovering, with and without blade stubs for several values of flow rates of the principal and by-pass duct.
...As a matter of fact, a remarkable total pressure saving was found with the stubs-off model.
Unfortunately, the presence of the rotating hub significantly reduced the gain. In fact, the total pressure is 6% higher with the optimized duct, but it must be considered that the stub blade makes much more disturbance that the real complete one as the tip of the stub, and consequently the tip vortex , is very close to the duct inlet.
https://cordis.europa.eu/project/id/619949/reporting
The three rotor head configurations are designated: H.1 - without blade stubs but with spacers; H2 - including both stubs and spacers; and H3 - including blade.
https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb...
Ref. also to:
- https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb...
--------------------------------------------------
Note added at 9 час (2020-02-10 08:13:25 GMT)
--------------------------------------------------
В некоторых случаях при изготовлении сварных рабочих колес с целью получения высокопрочного соединения применяется электро-шлаковая приварка лопасти не непосредственно к ступице, а к пенькам, отлитым на ее поверхности, при этом шов оказывается в зоне, достаточно удаленной от места наибольших напряжений. Но при совмещении лопастей с пеньками их профили часто не совпадают и пеньки приходится подрубать или наплавлять. Кроме того, омываемую поверхность ступицы не удается обработать на станке.
https://mash-xxl.info/info/337198/
...As a matter of fact, a remarkable total pressure saving was found with the stubs-off model.
Unfortunately, the presence of the rotating hub significantly reduced the gain. In fact, the total pressure is 6% higher with the optimized duct, but it must be considered that the stub blade makes much more disturbance that the real complete one as the tip of the stub, and consequently the tip vortex , is very close to the duct inlet.
https://cordis.europa.eu/project/id/619949/reporting
The three rotor head configurations are designated: H.1 - without blade stubs but with spacers; H2 - including both stubs and spacers; and H3 - including blade.
https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb...
Ref. also to:
- https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb...
--------------------------------------------------
Note added at 9 час (2020-02-10 08:13:25 GMT)
--------------------------------------------------
В некоторых случаях при изготовлении сварных рабочих колес с целью получения высокопрочного соединения применяется электро-шлаковая приварка лопасти не непосредственно к ступице, а к пенькам, отлитым на ее поверхности, при этом шов оказывается в зоне, достаточно удаленной от места наибольших напряжений. Но при совмещении лопастей с пеньками их профили часто не совпадают и пеньки приходится подрубать или наплавлять. Кроме того, омываемую поверхность ступицы не удается обработать на станке.
https://mash-xxl.info/info/337198/
4 KudoZ points awarded for this answer.
Comment: "Thank you!"
1 hr
without blades
Ступицы 5 (рис. 4.2, б) сварных рабочих колес выполняются литыми, с прилитыми частями 6 лопастей (пеньками) или без них
http://www.stroitelstvo-new.ru/gidroturbina/img/4-4.png
1 — направляющий подшипник; 2 — вал турбины; 3 — припасованный болт; 4 — ступица; 5 — уплотнительное кольцо ступицы; 6 — верхнее неподвижное уплотнительное кольцо; 7 — лопасть; 8 — обод; 9 — уплотнительное кольцо обода; 10 — нижнее неподвижное уплотнительное кольцо.
http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab...
лопасть турбины f—turbine blade n
https://www.linguee.com/russian-english/translation/лопасть....
http://www.stroitelstvo-new.ru/gidroturbina/img/4-4.png
1 — направляющий подшипник; 2 — вал турбины; 3 — припасованный болт; 4 — ступица; 5 — уплотнительное кольцо ступицы; 6 — верхнее неподвижное уплотнительное кольцо; 7 — лопасть; 8 — обод; 9 — уплотнительное кольцо обода; 10 — нижнее неподвижное уплотнительное кольцо.
http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab...
лопасть турбины f—turbine blade n
https://www.linguee.com/russian-english/translation/лопасть....
Reference comments
21 hrs
Reference:
Дима, посмотрите рис.6
https://pdfs.semanticscholar.org/adb9/c8f05419403a05f0f0c329...
I hope that helps
--------------------------------------------------
Note added at 1 day 17 hrs (2020-02-11 15:49:20 GMT)
--------------------------------------------------
и вот тут ещё рис.4,2
http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab...
https://pdfs.semanticscholar.org/adb9/c8f05419403a05f0f0c329...
I hope that helps
--------------------------------------------------
Note added at 1 day 17 hrs (2020-02-11 15:49:20 GMT)
--------------------------------------------------
и вот тут ещё рис.4,2
http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab...
Note from asker:
Спасибо! Почитаю -- может еще что-то интересное найду в статье |
Discussion